Friday, November 13, 2009

Spraying Sealer on Gun Cabinet.


Finally the weather is beginning to break and I'm going to do some spraying. It's been raining for the past few days, so I don't do any spraying in weather like that. Too much moisture in the air. We took a few pictures while I was spraying the sealer coats. As you can see in the pictures, I left the doors, backs, drawers, shelves and all the hardware off the cabinets.


If you click on the pictures, you will see the doors and shelves in the back ground (they already have two coats of sealer sprayed on them). I have the base turned upside down so I can spray sealer on the bottom so everything will be sealed equally.



If you look closely on the second picture, you can see where I'm spraying how the color changes when the sealer is applied. I will spray two coats of sealer on the bottom, then when dry, I will flip the cabinet right side up and spray all the rest of it with two coats of sealer.




The sealer begins to bring out the warm golden brown color the fuming did to the white oak and it gets richer with each coat.

I have an installation in Raleigh, NC. tomorrow so will leave early in the morning and I'm sure it will be quite late by the time I get home tomorrow night. No chance of working on the gun cabinet tomorrow........but that's a good thing. This will give the sealer a long time to dry and will be ready to sand. I will sand everything (inside, outside, top and bottom). Once everything is sanded with 220 grit sandpaper and wiped down real good, I'll be ready to start spraying the clear top coat. I will be using ML Campbell pre-catalyzed lacquer (15 sheen) for the final finish. Again, two coats on everything.

OK, that's enough for tonight, I've got to get the Van loaded for tomorrow so I can hit the road early.

Wednesday, November 11, 2009

"Fuming" the gun cabinet


I haven't posted in a week or so, but that's not because I haven't been working on the gun cabinet.


I finished all the building process this past week and now it's time to start the finishing process. I'm doing a little different process then is normally done when finishing. Usually we would pick out a color of stain to use and stain the entire cabinet before applying the actual finish, but I will be "fuming" the gun cabinet instead of staining.



Note of interest: Ammonia fuming is a traditional process for darkening and richening the color of Oak. Supposedly it was discovered by observing the way that oak beams in stables were darkened on exposure to the fumes from horse urine. Thanks to Haber and Bosch, we can now do this with convenient ammonia, and I don't need to keep a horse in the shop!....in modern times, ammonia fuming is best known through the work of Gustav Stickley ( Stickley Furniture).


And you ask.....How do I do it? The first thing I have to do is build a "tent" or "box" big enough for the cabinet to fit in and be able to seal it off pretty tight. This I did on our back porch pad using some of my scrape plywood along both sides and one end. I did a double layer of plastic across the top and down the other end ( this I will use for the door to be able to put the cabinet in.




If you look closely, you can see I already have the cabinet in the "box". You don't want the box any bigger then it needs to be so you can get the best concentration of fumes from the ammonia

You're not able to see in the picture, but I removed the doors, drawers, drawer fronts and all the hinges and drawer slides. Ammonia could be corrosive to the slides and hinges. I also didn't want any of the doors or drawer fronts to be covering part of the cabinet (this would leave a tan line when fumed.) I will have to do the doors, drawer fronts and shelves in the next batch.


Now it's time to put the ammonia in the box. I used 4 plastic open containers and filled each about a 1/3 of the way.



You'd think I was working with nuclear waste or something the way I'm dressed, but just following directions. I placed one container on each side of the cabinet and one in front and one behind the cabinet. Once they where in place, I closed the box up and sealed if off the best I could.




How long do I leave it in there? I read anywhere from 12 to 48 hours, but once it gets to a certain point, it will not get any darker. I did a little experiment before I did the cabinet. I took 3 pieces of oak and put them in a small sealed container with some ammonia so I could see the reaction from different times. I took the first piece out after just 6 hours and was surprised how much it had changed. It had such a warm brown look to it. I took the second piece out after 12 hours and could see a difference from the first piece. I left the 3rd piece in for 24 hours and when I took that one out that was quite a bit darker then the first two. I sprayed all three with the Lacquer I will be using for the finish to see what the final result was. Wow! there is no way you can achieve that look with stain. I was impressed!


After comparing the three samples, I liked the second one the best.(12 hours). Not too light.....and not too dark...... But just right! So here I go with the big piece. Boy was I nervous! If I screw this up after all the work I've put in it, I'm not sure what I'll do.


It's 8:30AM and it's in the "box". I'll come back at 8:30 tonight and see what I've got! Not really, I checked on it a couple times during the day and when I pulled it out at 8:30 PM ,I compared it to the samples I made and realized that the tone was about the same as my sample @ 6 hours, so I figured the size of the box compared to the small container I had the samples in and the amount of ammonia compared to the size, it would just take longer to achieve the same tone........So back in the box and sealed it up again. This time I pulled it out after a total of 24 hours of fuming and Wham! there it was. The look I wanted.


I pulled the cabinet out and decided it was time to do the doors, drawer fronts and shelves. This was a little tricky because you can't just lay them down, because it won't fume if it doesn't get air circulation around it, but I hung the upper doors and used some special painters pyramids to support the drawer fronts, shelves and lower doors. Back to the box, added a little fresh ammonia and sealed it up again. This time I left them for a straight 24 hours and then checked them. Perfect! This is so cool.



Sorry, I'm not posting any more pictures until it's delivered to Pennsylvania! The rest has to be a surprise for everyone. BTW.....It's been raining for the past 2 days and I haven't been able to do any spraying, but it is suppose to clear up by this week end and the clear finishing is easy. I've ordered the hardware and as soon as I get the upper doors finished, I'll take them to the glass Co. and let them install the glass.


It won't be long now!!

Wednesday, October 28, 2009

#8 Gun Cabinet, top section assembly

It's time to put the top section together. This is quite large, so will be fun to accomplish this in my small work space. The first thing I did was rip the front and back edge of the bottom shelf @ 4 degrees. I want the bottom shelf to set at a 4 degree angle so this will automatically tip the weapons to the back of the cabinet. This will make more sense when I make the bottom divider for the gun stocks.

I pre-drilled the top and bottom shelves for the pocket screws like I did on the base unit. Once the shelves where mounted to the side panels I mounted the face frame. Glued, screws along the top and bottom and clamped along the side.



I left everything on clamps overnight. Once the clamps came off, I sanded the face frame to the side panels. I cut the crown molding and it was mounted with screws from inside the cabinet. Again, NO NAILS. If you haven't noticed by now..........I really don't like nails. The crown molding is mounted flush with the top of the cabinet and since it's made with 3 solid pieces of OAK, there is no void or open area between the top of the crown and the cabinet.(makes a solid flat top all the way to the front edge of the crown.

I measured, cut, sanded and mounted the backs for both the base and upper section.(the backs are also mounted with screws). I mounted the hinges on the doors and hung the doors. The next step will be to make the top for the base unit, between the base and upper unit and then it will be time to do the inside of the upper section. Making the upper strip for the barrels of the guns and make the base strip for the stocks. I have a unique idea about how I want to do the upper strip so this will take a little time working out the details.

I just put the two sections together, so lets scroll down and take a look.


Keep going!

Keep going!

Almost there.........



There it is.......... Whatcha think? Is it beginning to look like a gun cabinet?

The counter top on the base section will finish off the overall look and tie the two section together and the hardware will give it the finished look.

Friday, October 23, 2009

#7 Gun Cabinet assembly

For the past couple weeks I've been building components for the gun cabinet. I know this is taking a long time, but I'm also trying to stay on schedule with a few other projects, so I've had to divide my time.


I think it's time to start putting this bad boy together!

I'm going to start with the base unit. I cut the bottom shelf to exact size using 3/4" Quarter Sawn White Oak Plywood. I built a frame for the top of the base unit, since there will be a top between the base and the upper unit. Once they were sanded, I drilled the pocket holes with my Kreg pneumatic pocket hole machine on the bottom side of the bottom shelf and the frame.



If you click on the pictures, you can see how I drilled the ends of the shelf and frame and also along the front edge.



The holes on the ends will be used to fasten the shelf and frame to the end panels. The holes along the front edge of the shelf and frame will be used to attach the face frame once the sides are mounted.

Here I'm attaching the sides to the shelf and frame.



Now I can mount the face frame. Glue and screws will hold it all together. NO NAILS! While the face frame is on clamps, I went ahead and mounted the base board molding (again, done with screws from the back side, so no fastening is visible) Again NO NAILS. I've used over 50 screws so far just assembling the base.



Glue is dry, clamps come off and the base board molding is mounted. I then mounted the center divider, drilled for adjustable shelves and made two shelves. I mounted the doors, made the mounting stringers for the drawer slides and mounted the drawer slides. Installed the drawer boxes and mounted the drawer fronts.



The only thing left to do for the base is cut the back, mount hardware and locks. The base is about ready for the final sanding.

I'll start the assembly of the top unit next.

Thursday, October 22, 2009

#6 Gun Cabinet Moldings


Wow, here it is Thursday evening already. This week has gotten away from me. Monday I finished up a cedar chest I was refinishing for a customer. (that's a whole story in itself, but I'm not going there!). Delivered it Wednesday and the customer loved it. Tuesday I went to Gibsonville, NC to pick up the last of the lumber I needed for the gun cabinet and lumber for the next two projects I'll be starting next week. Almost 5 hours each direction and a couple hours at the lumber store makes for a long day.



I've run all the stock for the moldings. The crown molding will be a 3 piece molding, which is my signature molding I use on a lot of my pieces. It has a traditional look, but definitely has a different profile than a regular store bought molding.




I have the first two profiles for the crown molding on clamps. Once they dry, I'll pull all the clamps and glue up the third section of the crown




I wanted to get the last of the crown molding on clamps before I called it a day. I did the drawer fronts earlier today, so this is pretty much the last of the components.






I'll start assembly now that all the components are done. I'll be cutting the 3/4" plywood for the bottoms and tops.

It's going to start looking like a gun cabinet before long, instead of a bunch of pieces. STAY TUNED!

Friday, October 16, 2009

#5 Making the drawers for the gun cabinet.

I'm making the drawer boxes out of Maple. I ripped two boards (6 ft length) to 3 1/2" width and planed to 5/8" thickness. I ran a 1/4" daddo for the bottoms. (They're shown below, leaning against the faceframe).


Once that was done, I cut the pieces to the proper length for the sides, fronts and backs. I then laid the drawers out so I could mark them for dovetailing. Each piece is placed up side down and inside out and marked, so when I dovetail each corner it turns out right. I know that's confusing, but for me that comes natural (another words, it's easy for me to think backwards.) LOL.

See how I marked each corner. I do that so I can keep track of proper alignment for each corner when putting them in the dovetail jig.


I use the Porter Cable Omni Jig to do my dovetails. I leave one of my routers set up with the proper bit all the time to save on set up time. It's very critical to have the bit set exactly perfect to get a good dovetail. (that's why it's worth designating a router just for this function.) This router is left set up for dovetailing and never used for anything else.

Once all the pieces are dovetailed they are ready for assembly. Measure and cut the bottoms and glue the drawers together. I cleaned all the joints with a damp rag to remove any excess glue. I don't have to clamp the drawers, but I do check to make sure they are square and will leave them over night to dry. Tomorrow I will do the final sanding and notch the bottom back for the blum undermount slides I plan on using.


I didn't take any pictures, but when I took the doors off the clamps, I sanded them one more time to make sure all joints are flush. I rabbited the back of the top doors to allow for the glass.
I also ran the profile around the doors and cut the notches for the hinges. I'm using the Youngsdale #6 knife hinge.
Everything will be sanded one more time after the cabinet is assembled. ( actually it will be assembled, then taken apart again to be sanded before finishing).
It won't be long now before I start assembly and that's when all these pieces begin to make more sense. I probably build a little differently then most, but I like to take my time and build all the components before I actually assemble it.


Tuesday, October 13, 2009

#4 Making the doors for the Gun Cabinet

Yesterday I glued up the panels for the bottom doors. As you can see in the picture, I glued up one large panel and I'll cut the two panels from the one board so they match.

While my panel was on clamps, I took the end panels off their clamps and sanded them (they will be sanded again when the cabinet is assembled. The Face Frames are sanded, but again, they will be sanded again when everything is assembled.

Once all the stock was sized for the door frames, I ran them thru the door machine and sanded each piece. I took the panel off the clamps and cut the two panels to size and ran them thru the door machine. Sanded the panels and assembled the doors. The doors are on clamps now, so will leave them overnight.

It's about time to think about dovetailing a couple drawer boxes, but that's on tomorrows agenda.
While I'm working on the gun cabinet, I'm also building some shelves for one of my customers, refinishing a cedar chest for another customer and finishing up two bandsaw boxes for another. I have a couple kitchen cabinets to build, but I won't start them until the end of the week.